Cold water inlet and non return valve for Carver Water heater. Situated at bottom right hand corner when looking at rear of heater.
7 Technical Questions on the Cold water inlet and non return valve for Carver Water heater
Carver Cascade II. Re carver water heater 11. cant get rid of the air in my water heater. was wondering if there is a one way valve needs replacing any help would be good for the part i require
you would need to ask our technical team, they have engineers available for answering the questions
It is possible that the cold water feed connection that includes a non return valve could be faulty. Our ref 128606.
Hi There, My carver2 run hot water tap doesn't flow and the water in the aqua roll is getting very hot . I noted in one of your previous mails that there is a return valve in line , if you think this is also my problem do you have a part number so I can get one ordered from you please.....or do you have any other thoughts??
Important to change the non-return valve first, our ref. 128606. This is positioned at the bottom right hand corner of the heater and is connected to the blue piping.
the hot water on my carver cascade 2GE goes to a dribble after about 10/15 seconds and eventually stops. the cold water is working fine
by Steve Oraa
It is almost certainly a problem with the non return valve at the water heater. This is combined with the cold water inlet fitting that you will find at the bottom right hand corner of the heater when looking at the inside. It is probably best to replace the fitting, our ref. 128606, which unscrews from the heater. The original fittings were white in colour.
I have a Coachman 1992 VIP fitted with a Carver Cascade 2 water heater. The cold water inlet coupling at the bottom left facing the van has sheared off at the point of entry. The fitting looks similar to your part 119476 except that the right hand end is longer and is ribbed to secure it into the hose. Do you have a suitable part or could I use 119476. If so how do I get a good connection to the hose
by Brian Clarke
The cold water inlet has a non return valve incorporated and is our part 128606. This is suitable for connecting to flexible hose with a hole clip.
how do yo fill a carver cascade mk 2 water heater with water i have just bought the van and not sure how to work it the pump is new but doesn't pump water into the tank
by Mark Marsh
Assuming that you have water coming from your cold tap when the pump is operating, then there must be a blockage in the feed to the Carver heater. This is most likely caused by a faulty cold water inlet connection which screws into the tank at the bottom right hand corner. If you remove this part from the tank and ensure that the check valve inside is free to move. If not then you may need to replace the fitting, our ref. 128606.
need to change cold water valve bottom right looking from back on a carver cascade 11 but not sure what valve it is its a white in color i notice 2 in the pats list
by Darren Holden
This is our part 128606, colour now black.
Hi, I have a 1992 Abbey Stafford with a carver water heater. The hot water doesn't flow as fast as it used to and I wondered what was wrong with it please.
This is possibly caused by the cold water non-return valve sticking. This is the cold water inlet to the water heater but of course controls the flow of water coming out of the heater.
17 Customer Reviews on Cold water inlet and non return valve for Carver Water heater
Perfect Part But Prepare For Fitting
by David Cross (09 Apr 2019)
Totally correct replacement. Please ensure you prepare the threads of the cast aluminium heater section prior to any attempt to fit. Should you fail to clean the threads there is a chance you could break the replacement part as you tighten it against the shoulders of the nut section. I used a liquid gasket product used by plumbers which acted as a lubricant and also ensured a seal where the aluminium threads had corroded.
Does What Says
by Ray smith (01 May 2018)
Very soft plastic, watch the spanner if it jumps it rounds the nut
by John Stephenson (21 Aug 2017)
This was perfect for the job. These plastic bits in my 20+ year old carver have all started to disintegrate and I was pleased to get bits that fitted. Delivery was prompt so I could get on with the job. The only down side was removing the old fittings.
Carver Non Return Valve
by mr aldridge (26 Apr 2017)
Arrived quickly not fitted yet so cannot comment on fitting
by Mr Wilcox (02 Oct 2014)
Fast delivery, part exactly as described, heater working again. Many thanks.
by Mr Bleach (20 Aug 2014)
Great piece of kit. much better than the original. needed this in a urgently, Well satisfied, good fast service,
Carver Cold Water Inlet Valve
by Mr Oakley (04 Jun 2014)
very fast service. Thanks
by Mr Dickson (20 Nov 2013)
Arrived by return and installed, OK so far, not yet long term tested.
Cold Water Fitting For Carver Heater
by Mitsu Alan (04 Oct 2013)
Purchased this along with hot water outlet. Removed Carver heater from motorhome to readily access remnants of old fittings that left threaded segment in hole. Threads are M16 x 2mm. Used Sikaflex 512 product to re-seal unit heater in place.
Hot Water Outlet Carver Water Heaters
by Mr Grant (31 Jul 2013)
exactly what I ordered good quality fast delivery great service
Carver Cold Water Inlet
by Mr Hill (25 Oct 2012)
Bought as spare with hot water inlet. Looks stronger than original and arrived next day.
by Mr Carnill (01 Aug 2012)
brilliant service many thanks
Carver Water Heater Non-return Valve.
by JimH (08 Jun 2012)
Exactly what it said it was, very quick delivery
Replaced the obstructed one in our carver water heater.
Cold Water Inlet And Non-return Valve
by Mr Lines (12 Jul 2011)
Ideal for the job - fast delivery. Brilliant
Cold Water Inlet And Non-return Valve
by Mr Robinson (10 Mar 2011)
Fast delivery. Fitted OK, after female threads had been cleared of limescale. Initial test shows correct function. Thanks.
by Richard (22 Oct 2010)
Got my heater working again no fuss, fast efficient delivery
by Dave (19 Feb 2010)
Great service, part as required. Good Price
Did you know we have been established and have been in the caravan and motorhome industry for over 50 years?
Low Rate CreditAvailable on 12, 18, 24 or 36 month terms. Spread the cost of your purchase with a low rate 14.9% fixed rate APR.
Leisureshopdirect Ltd is an introducer of regulated credit products provided exclusively by Close Brothers Retail Finance. Close Brothers Retail Finance is a trading name of Close Brothers Limited. Finance is only available to permanent UK residents aged between 18-75, subject to status, terms and conditions apply.
For further information, please visit our finance page: Finance Page Examples The below example takes just the value of this product. There may be further costs such as shipping which have not been taken into account. To see a final figure please continue to checkout.
As you are an international customer, we can't calculate your shipping price automatically. You will notice that it has defaulted to £1000.
Please click the 'Send Shipping Request' button below and we will then work out the shipping cost and email you a link that will allow you to pay securely for the complete order. This usually takes much less than one working day.